By Israel Kaplan · Updated 2026-10-20
Short answer: A full interlock driveway in the GTA typically costs $28 to $40 per square foot installed, before HST. An 800 sq ft (20 x 40 ft) driveway usually lands between $22,400 and $32,000. Paver choice, access, existing asphalt or concrete removal, and base depth move the number. A paver border and apron costs $3,500 to $6,000.

What does a full interlock driveway cost per square foot?
Our full paver driveways run $28 to $40 per square foot installed, before HST. That price covers excavation and disposal, geotextile fabric where the soil needs it, a compacted 3/4 clear gravel base, the bedding layer, vehicular-grade pavers, edge restraint, polymeric sand, compaction and cleanup.
The range is wide because a driveway is not one product. A standard 60 to 80 mm paver from Unilock or Permacon sits at the low end. Large-format slabs, natural stone and porcelain sit at the top.
What do typical driveway sizes cost in total?
An 800 sq ft driveway (20 x 40 ft) typically lands between $22,400 and $32,000. A 1,000 sq ft driveway lands between $28,000 and $40,000. These totals are before HST, for a standard paver on a lot with normal access.
To estimate yours, measure the length and width of the area to be paved, multiply them, and then multiply by $28 and by $40. That gives you the bracket. The on-site estimate turns the bracket into one number.
Why does a driveway cost more per square foot than a patio?
Depth. A driveway carries cars, so it needs 10 to 12 inches of compacted gravel base, laid in 3-inch lifts. A patio or walkway needs 6 to 8 inches. More base means more excavation, more stone delivered and more soil hauled away.
On the clay soils common in Vaughan, Markham and Richmond Hill we also put woven geotextile fabric under the base. It is cheap compared with fixing ruts later, and it is one of the first things a low quote leaves out.
What moves the price of an interlock driveway up or down?
Five things matter most. Paver choice is the biggest swing. Access is next: if a mini-excavator and a skid steer can reach the work area, excavation and base delivery are fast, and if everything has to go through a narrow gate by wheelbarrow, it adds labour.
Removing an existing driveway adds cost. Breaking out and disposing of old concrete or asphalt adds roughly $3 per square foot, so an 800 sq ft driveway adds about $2,400. Bare lawn is the cheapest starting point.
Grade and extras finish the list. A sloped lot may need a retaining wall and steps, which are priced separately by face area. Borders, inlays, lighting conduit and 3D design are optional and quoted line by line.
Is a paver border and apron a cheaper way to get the look?
Yes. If a full paver driveway is not in the budget, a 12 to 18 inch paver border on each side, a paver apron at the garage and a matching front walk give you most of the look for a fraction of the cost. A typical two-car border package is $3,500 to $6,000.
For borders and aprons we saw-cut the asphalt and build the paver section beside it. The asphalt stays. A full paver driveway is different: asphalt cannot be the base, so it has to come out first.
What should I check when comparing driveway quotes?
Ask each contractor four things: how deep is the compacted base, is there geotextile fabric under it, what edge restraint is used, and what is the warranty? Two quotes that look similar per square foot can hide very different bases.
Our price includes the base depth, geotextile, compaction and edge restraint described above, and every installation comes with a 2-year workmanship warranty. On-site estimates are free and come with a written quote within 48 hours. Our minimum project size is $2,500.
Prices: see our pricing page and our interlock driveways page.